Image is for illustration only and should not be relied upon Honeywell CM901 / CM907 / T4 Remote Sensor

Honeywell CM901 / CM907 / T4 Remote Sensor

0 reviews

£35.69

Ex VAT: £29.74

Brand: Resideo (Honeywell)

HCO Code: 05A01

Availability: In Stock

Remote Sensor for CM901/CM907/T4 thermostats.

NOT FOR USE ON CM61/CM67 SERIES.

NOT FOR USE ON CMT921/CMT927 THERMOSTATS

Only 1 wired-in sensor may be used at a time

Model: F42010972-001

Write a review

Your Name

Your Review

Note: HTML is not translated!

Rating Bad Good

Captcha

Please complete the captcha validation below

Expand All

The Honeywell remote sensor is in our lounge. Honeywell 907 readout in our hall. Ground source heat in the garage set to receive temp data from lounge Honeywell sensor, rather from its ground source unit's own settings. Hall Honeywell 907 shows lounge is 12C, yet lounge is 20C. It the remote sensor broken?
Two wires attached to the Honeywell room sensor ....., Are the two wires
connect to either terminal the wrong way around?
Is there anything any else that could be sending the incorrect lounge temp to the
hall's Honeywell 907? Answers1

It doesn't matter which way the wires are connected. As long as the connections are tight, then the fault must be with either the sensor or the CM907.

I have a T4 thermostat which is great, except for the very loud clicking of the relay compared to my last stat. If I buy this sensor should I then be able to relocate the T4 into the garage put this sensor in the T4's current position, eliminating the noise in the main house? Answers1

Yes it would be ideal for that.

Can the value from the sensor be used for certain hours during the day, and the other value from the CM907 for other hours of the same day? Answers1

I'm afraid not.

Can you let me know the dimensions of the unit please? Answers1

It is 72.5x70x29mm HxWxD

Is there an option on the CM907 to connect a Wi-fi adapter to enable a remote Wi-fi thermostat sensor in another room without the need for running a wire? Answers1

I'm afraid not

Our thermostat sits in the kitchen. It switches off too quickly as the temperature in the kitchen is higher than the rest of the house. Would this sensor be ok perhaps on the landing as this would allow the rest of the house to become the desired temp. Thanks Answers1

Assuming your thermostat is one of the ones listed, then yes. You will need to run a cable from the thermostat to your desired sensor location.

Can you recommend a minimum cable size to connect this unit, thanks. Answers1

It depends on the length. If it is just a short run, then you can use bell wire.

Hi I have a cm907 and it's in the master bedroom. It was placed near doorway and now a bookcase is on other side of it so it says the temp is hotter quicker than it is as air from window can't cool sensor. So I was thinking of buying this remote one to install in landing or nearby room(master bedroom doesn't need to be that hot) will this work and is it easy to do myself or should I call someone out. Thanks Answers1

Hi. Yes it would be suitable. You just need to run a cable from the CM907 to the sensor.

Hi Is this low voltage powered or 230v? Thanks Answers1

It's powered by the CM910 or CM907. It is a low voltage.

The boiler and cm907 is in a cold utility room so upstairs gets very warm. Can the remote temp sensor stay upstairs in my child's room to achieve the perfect temp? Answers1

Yes, as long as the cable to it is less than 50m.

Will this work as the only temperature sensor or as an or style function. Eg if a or b < desired temp fire until temp is reached on both? Answers1

No, once installed and enabled, this will work as the only temperature sensor.

is this compatible with any of honeywells internet connected stats? Answers1

No it isn't.

I've opened up my CM907 & there are no terminals where this sensor wires to (symbol is there on the plastic), are they supplied with the remote sensor? If not what is the part code for those? The CM907 has the pins where these plug into so must support it. Answers1

Yes the required terminal block is included with the sensor.

Showing 1 to 13 of 13 (1 pages)

More

Honeywell CM901 / CM907 / T4 Remote Sensor

Write a review

Legal

My Account

Information

Extras

Contact Us

High Quality

Awesome Support

Really Fast Deliveries

14-Day Returns

Secure Checkout